01 July, 2020

All About Pinpoint 300-815 Test Engine

we provide 100% Guarantee Cisco 300-815 free question which are the best for clearing 300-815 test, and to get certified by Cisco Implementing Cisco Advanced Call Control and Mobility Services (CLACCM). The 300-815 Questions & Answers covers all the knowledge points of the real 300-815 exam. Crack your Cisco 300-815 Exam with latest dumps, guaranteed!

Cisco 300-815 Free Dumps Questions Online, Read and Test Now.

Page: 1 / 0

Total 0 questions Full Exam Access

Question 1

Refer to the exhibit. Calls incoming from the provider are not working through newly set up Cisco Unified Border Element. Provider engineers get the 404 Not Found SIP message. Incoming calls are coming from the provider with called number “222333444” and Cisco Unified Communications Manager is expecting the called number to be delivered as “444333222”. The administrator already verified that the IP address of the Cisco Unified CM is set up correctly and there are no dial peers configured other than those shown in the exhibit. Which action must the administrator take to fix the issue?

Change the destination-pattern on the outgoing dial peer to match “444333222”.

Set up translation-profile on the incoming dial peer to match incoming traffic.

Create specific matching for “222333444” on the incoming dial peer.

Fix the voice translation-rule to match specifically number “222333444” and change it to “444333222”.

Question 2

The Cisco Unified Communications Manager Dialed Number Analyzer allows analysis of calls from which two devices? (Choose two.)

translation patterns

device pools

CTI ports

CTI route points

IP phones

Question 3

What is a component of Cisco Unified Mobility?

Unified IVR

Mobile Connect

Smart Client Support

Single Number Connect

Question 4

In Cisco Unified Communications Manager, which tool do you use to check SIP traces?

MTP

CCSIP

RTMT

OS Administration Page

Question 5

Configure Call Queuing in Cisco Unified Communications Manager. Where do you set the maximum number of callers in the queue?

in the telephony service configuration

in the queuing configuration

in Cisco Unified CM Enterprise Parameters

in Cisco Unified CM Service Parameters

Question 6

A user in location X dials an extension at location Y. The call travels through a QoS-enabled WAN network, but the user experiences choppy or clipped audio. What is the cause of this issue?

missing Call Admission Control

codec mismatch

ptime mismatch

phone class of service issue

Question 7

Which two types of authentication are supported for the configuration of Intercluster Lookup Service? (Choose two.)

TokenID

username and secret key

TLS certificates

passwords

FQDN of the servers defined in DNS

Question 8

An administrator is configuring a cluster for ILS and wants to limit the amount of entities that Cisco Unified Communications Manager can write to the database for data that is learned through ILS. Which service parameter is used to adjust this limit?

ILS Max Number of Learned Objects in Database

ILS Active Learned Object Upper Limit

Global Data Service Parameter Limit

Imported Dial Plan Replication Database Object Lower Limit

Question 9

Refer to the exhibit. How many maximum hops can an ILS updarte traverse?

Question 10

A user reports when they press the services key they do not receive a user ID and password prompt to assign the phone extension. Which action resolves the issue?

Create the default device profiles for all phone models that are used.

Subscribe the phone to the Cisco Extension Mobility service.

Create the end user and associate it to the device profile.

Assign the extension as a mobile extension.

Question 11

When the services key is pressed Cisco Extension Mobility does not show up. What is the cause of the issue?

The URL configured for Cisco Extension Mobility is not correct.

Cisco Extension Mobility Service is not running.

The phone is not subscribed to Cisco Extension Mobility Service.

Cisco Extension Mobility is not enabled in the Phone Configuration Window (Device > Phone)

Question 12

Which action is correct with respect to toll fraud prevention configuration in the Cisco Unified Communications Manager Express?

Configure Direct Inward Dial for Incoming ISDN Calls with overlap dialing.

Configure IP Address Trusted Authentication for Incoming VoIP Calls.

Configure the command no ip address trusted authenticate under “voice service voip”.

Enable Secondary Dial tone on Analog and Digital FXO Ports.

Question 13

Refer to the exhibit. An administrator is troubleshooting a situation where a call placed from a phone registered to Cisco Unified Communications Manager does not complete. The administrator wants to use the Dialed Number Analyzer on Cisco Unified CM to check which translation pattern the call is matching. However, when logging in to Cisco Unified Serviceability there is no option for Dialed Number Analyzer under the tool menu. Which two steps must be performed to resolve this issue? (Choose two.)

Restart the subscriber

Activate the Cisco Extended Functions service.

Activate the Cisco CallManager service.

Activate the Cisco Dialed Number Analyzer service.

Activate the Cisco Dialed Number Analyzer Server service.

Question 14

In Cisco Unified Communications Manager globalized call routing is implemented and must confirm that it is correctly implemented without making a call. Which tool do you use for verification?

Dialed Number Analyzer

Real-Time Monitoring Tool

SDI trace

SDL trace

Question 15

What is the relationship between partition, time schedule, and time period in Time-of-Day routing in Cisco Unified Communications Manager?

A partition can have multiple time schedules assigne

A time schedule contains one or more time periods.

A partition can have one time schedule assigne

A time schedule contains one or more time periods.

A partition can have multiple time schedules assigne

A time schedule contains only one time period.

A partition can have one time schedule assigne

A time schedule contains only one time period.

Question 16

An engineer must configure a secure SIP trunk with a remote provider, with a specific requirement to use port 5065 for inbound and otubound traffic. Which two items must be configured to complete this configuration? (Choose two.)

Incoming Port in SIP Information section of the SIP Trunk configuration.

Incoming Port in Security Information of the SIP Profile configuration.

Destination Port in SIP Information section of the SIP Trunk configuration

Incoming Port in SIP Trunk Security Profile configuration

Destination Port in SIP Trunk Security Profile configuration

Question 17

A user reports that when they attempt to log out from the Cisco Extension Mobility service by pressing the Services button, they cannot log out. What is the most likely cause of this issue?

The Cisco Extension Mobility service has not been configured on the phone.

There might be a significant delay between the button being pressed and the Cisco Extension Mobility service recognizing i

It would be best to check network latency.

The user device profile has not been assigned to the user.

The user device profile is not subscribed to the Cisco Extension Mobility service.

Question 18

Refer to the exhibit. Within the North American Numbering Plan, gateways located in Ottawa, Canada and marked as “YOW” are assigned to the Calling Party Transformation CSS NANP_CgPTP, which contains partition NANP_calling_xforms. What is the calling-party number and the numbering type if the calling user +1613-555-1234 dials the number?

calling number 613-555-1234 and numbering type “subscriber”

calling number 011-1-613-555-1234 and numbering type “subscriber”

calling number 011613-555-1234 and numbering type “international”

calling number 613-555-1234 and numbering type “national”

Question 19

What are the elements for Device Mobility configuration?

physical location, device pool, and Device Mobility group

device pool, Device Mobility group, and region

physical locatio

Device Mobility group, and region

device pool, Device Mobility group, and Cisco IP phone

Question 20

When configuring hunt groups, where do you add the individual directory numbers that will be part of the group?

route group

line group

hunt list

hunt pilot

Question 21

End users at a new site report being unable to hear the remote party when calling or being called by users at headquarters. Calls to and from the PSTN work as expected. To investigate the SIP signaling to troubleshoot the problem, which field can provide a hint for troubleshooting?

Contact: header of the 200 OK response

Allow: header if the 200 OK response

o= line of SDP content

c= line of SDP content

Question 22

Which description of RTP timestamps or sequence numbers is true?

The sequence number is used to detect losses.

Timestamps increase by the time “carrying” by a packet.

Sequence numbers increase by four for each RTP packet transmitted.

The timestamp is used to place the incoming audio and video packets in the correct timing order (playout delay compensation).

Question 23

An engineer is configuring a call park feature in Cisco Unified Communications Manager Express. Which command does the engineer use to ensure that the call is reverted to the user after 60 seconds?

R2(config-ephone-dn)#park reservation-group 60

R2(config-ephone-dn)#park-slot timeout 60 limit 2 recall alternate 3002

R2(config-ephone-dn)#park reservation-group 1

R2(config-ephone-dn)#park-slot timeout 30 limit 2 recall alternate 3002

Question 24

A support engineer is troubleshooting a voice network. When conducting a search for call setup details related to calling search space issues, which trace files should be investigated?

CallManager traces

CTI Manager traces

Cisco IP Manager Assistant

Call logs

Question 25

Which two statements are correct with respect to the Client Matter Code setting in the route pattern configuration? (Choose two.)

The Client Matter Code feature does not support overlap sending because the Cisco Unified CM cannot determine when to prompt the user for the code.

If you check the Allow Overlap Sending check box, the Require Client Matter Code check box becomes disabled.

If you check the Allow Overlap Sending check box, you can also check the Require Client Matter Code check box.

The Client Matter Code feature does support overlap sending because the Cisco Unified Communications Manager can determine when to prompt the user for the code.

The Client Matter Code has the option to configure Authorization Level such as in the Forced Authorization Code.

Page: 1 / 0

Total 0 questions Full Exam Access