29 January, 2020

Managing Industrial Networking For Manufacturing With Cisco Technologies 200-601 Software

Act now and download your Cisco 200-601 test today! Do not waste time for the worthless Cisco 200-601 tutorials. Download Abreast of the times Cisco Managing Industrial Networking for Manufacturing with Cisco Technologies exam with real questions and answers and begin to learn Cisco 200-601 with a classic professional.

Page: 1 / 7

Total 87 questions Full Exam Access

Question 1

Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link failure?

Rapid Per-VLAN Spanning Tree Protocol

Resilient Ethernet Protocol

Multiple Spanning Tree Protocol

Spanning Tree Protocol

Question 2

A ProfiNET management system operator is unable to see diagnostic information for a Cisco Industrial Ethernet switch that has been added to a SIMATIC management station. Based on the provided CLI output, which statement is correct?
switch# show profinet status State : Enabled
Vlan : 201
Id : IE2000-Switch Connected : Yes ReductRatio : 128
GSD version : Mis-match

The assigned ProfiNET VLAN is not valid and should be less than 100

LLDP has been disabled on this switch

The GSD file version on the switch does not match the GSD file version on the management station

The Reduction Ration has been set too low

Question 3

Exhibit:

Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which address is the default gateway of Host 3?

the address of the switch interface that is connected to router interface Fa0/0

the address of the switch interface that is connected to router interface Fa0/1

the address of the host that is connected to Network A

the address of the host that is connected to Network B

the address of the router interface Fa0/0

the address of the router interface Fa0/1

Question 4

What security component can be deployed to increase the defense in depth and specifically can be positioned against 'man-in-the-middle' attack?

Deploy 802.1AE

Deploy 802.1X

Deploy 802.1Q

Deploy 802.1AX

Question 5

Which of the following correctly pairs the dotted decimal subnet mask with the correct number of binary bits that represent the subnet mask?

255.255.255.192 and /25

255.255.255.248 and /28

255.255.255.224 and /26

255.255.255.248 and /27

255.255.255.240 and /28

255.255.255.240 and /16

Question 6

What percentage of an I/O connection would you set the RPI in order to ensure the application has the most current data?

RPI at 50% of IO rate

RPI at 25% of IO rate

PI to 25% of PAC scan rate

Set RPI to 50% of PAC scan rate

Question 7

Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching default criteria to 50?

ptp mode boundary ptp priority1 10ptp priority2 50

ptp mode boundary ptp priority1 50ptp priority2 10

ptp mode e2etransparent ptp priority1 50ptp priority2 10

ptp mode e2etransparent ptp priority1 10ptp priority2 50

Question 8

Which option best describes the ProfiNET Discovery and Configuration Protocol (DCP)?

Can be used to override both static and dynamically (DHCP/BOOTP) assigned IP addresses

Cannot be used to reset a device to factory defaults

Is only supported in Conformance Class B and C devices

Uses the ProfiNET-IRT communication class

Question 9

To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?

switch(config-if)#mls qos trust cos

switch(config-if)#qos trust cos

switch(config-if)#profinet cos trust

switch(config-if)#trust qos cos

Question 10

It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as opposed to the Enterprise where it is not generally deployed. What are two reasons why REP is more suitable for the plant floor? (Choose two)

REP is only supported on Industrial Ethernet switches, it is not supported on Catalyst switches.

REP converges faster than Spanning Tree, allowing for greater network availability.

REP supports Industrial Ethernet protocols better because it moves the packets faster.

Running dual cables from access switches to an aggregation switch can have a much higher cost on the plant floor than in the Enterprise and running a ring protocol like REP provides resiliency at a lower cost.

Industrial protocols can be negatively impacted by the number of nodes the Ethernet frame traverses, REP provides a topology with no more than 3 nodes for any data path.

Question 11

Refer to the exhibit.
200-601 dumps exhibit

NAT has been configured on the router 'GW' and the IP addresses of router 'GW' have been configured properly. Users of PC1 and PC2 are able to ping the IP address 198.51.100.1 but are unable to reach any other IP addresses on the Internet. The ISP confirmed that their configuration is correct. Which option would likely correct the problem?

ip access-list extended ACL_OUTBOUND permit ip 10.1.1.0 0.0.0.255 anyinterface Ethernet1ip access-group ACL_OUTBOUND out

interface Ethernet1 ip nat outside

interface Ethernet0 ip nat inside

ip route 0.0.0.0 0.0.0.0 198.51.100.1

Question 12

How are I/O timeout and Safety I/O timeout calculated?

An I/O connection will timeout based on the lower of 4x RPI or 100m

Safety I/O timeout is calculated as 4xRPI.

An I/O connection will timeout based on the lower of 3x RPI or 100m

Safety I/O timeout is calculated as 3xRPI.

An I/O connection will timeout based on the lower of 4x RPI or 150m

Safety I/Otimeout is calculated as 2xRPI.

An I/O connection will timeout based on the lower of 3x RPI or 150m

Safety I/O timeout is calculated as 3xRPI.

Question 13

Which two are possible solutions to control which devices can communicate between industrial zones? (Choose two)

Use per zone private IP addressing and deploy NAT to control traffic between zones

Put access control lists on switches connecting industrial zones to control traffic

Attach each zone to a firewall to control intra-zone traffic

Deploy QoS traffic shaping to limit the volume of traffic between industrial zones

Deploy an IDS system between the zones to control intra-zone traffic

Question 14

When troubleshooting a high packet loss condition in the network, the inspection area has an assessed M.I.C.E. value of M=1, I=1, C=3 and E=1. Which condition could be suspect?

Use of shielded Patch Cables, Bonded on one end only.

Use of unshielded Patch Cables.

Broken seal on bulkhead connector.

Oxidation on Shielded RJ45 Patch Plug

Question 15

Refer to the exhibit.
200-601 dumps exhibit

Which values are correct for AP 2 to allow for efficient roaming?

Channel 6, SSID Sittingduck, BSSID 00:0a:0b:0c:0d:0e

Channel 1, SSID Sittingduck, BSSID 00:01:02:03:04:05

Channel 1, SSID Sittingduck, BSSID 00:0a:0b:0c:0d:0e

Channel 6, SSID Sittingduck, BSSID 00:01:02:03:04:05

Question 16

Refer to the exhibit.
200-601 dumps exhibit

Which two parameters can be used to diagnose an overloaded system? (Choose two)

Ethernet Port 1 Speed

Module Resource Allocation Actual Rate

Class 3 Received bytes per second

Media Counters Alignment Errors

TCP Connections Active

Question 17

Refer to the exhibit.
200-601 dumps exhibit

All of the vlans listed in the routing table below are trunked using 802.1q and are active on all switches. PLC1, PLC2, and PLC3 each has IP address 192.168.0.1/24 and are connected to ports configured for vlan 50. L2SW1, L2SW2, and L2SW3 are not using vlan trunking for vlan 50.
L3SW1 has following routing table:
10.0.0.0/8 is variably subnetted, 12 subnets, 2 masks C 10.3.138.0/23 is directly connected, Vlan307
C 10.3.136.0/23 is directly connected, Vlan306 C 10.15.153.0/24 is directly connected, Vlan398 C 10.3.142.0/23 is directly connected, Vlan309 C 10.3.140.0/23 is directly connected, Vlan308 C 10.3.186.0/23 is directly connected, Vlan293 C 10.15.154.0/24 is directly connected, Vlan399 C 10.3.184.0/23 is directly connected, Vlan292 C 10.3.190.0/23 is directly connected, Vlan295 C 10.3.188.0/23 is directly connected, Vlan294
C 10.3.182.0/23 is directly connected, Vlan291 C 10.3.180.0/23 is directly connected, Vlan290
PLC1, PLC2, and PLC3 cannot be reconfigured. What can be done to be able to simultaneously communicate with PLC1, PLC2, and PLC3?

Enable NAT on L3SW1

Enable NAT on L2SW1 – L2SW3

Enable NAT on L2SW4

Add vlan 50 to L2SW4 and assign the administrator\'s an IP address on 192.168.0.0/24 network

Question 18

A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choose two)

DLR is designed for single network operation at the machine level

Moving to a linear topology will reduce the number of cables and so reduce risk of cable failure

DLR is the only resiliency technology that is supported by CIP Safety

Layer 2 resiliency protocols like REP and RSTP do not have a fast enough convergence time for motion control

Half of the network traffic goes clockwise on the ring and the other half counter- clockwise, reducing by 50% the impact of cable failure

Question 19

A small manufacturing company has a Class C network address on the plant floor and needs to create five subnets, each accommodating 25 endpoints. Which subnet mask needs to be configured?

255.255.240.0

255.255.255.128

255.255.255.192

255.255.255.224

255.255.255.240

255.255.255.248

Question 20

Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch?

switch#show snooping ip igmp

switch#show igmp snooping

switch#show ip igmp snooping

switch#show ip snooping

Question 21

Which in-depth approach is used when deploying defense in an industrial zone?

Use PLCs and control systems from multiple vendors in such a way that the process will become resilient for failures of one vendor.

Deploy two factor authentications for all operators which need to login remote while working from home.

Collect log files at a central location for easy back-up and encryption to provide privacy.

Create multiple zones in the industrial zone and protect / inspect traffic between the zones with firewalls and intrusion monitors.

Question 22

Refer to the exhibit.
200-601 dumps exhibit

CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this
marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1. You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in:
L2SW4# show mls interface GigabitEthernet 1/1 statistics

output queues dropped:
queue: threshold1 threshold2 threshold3 queue 0 0 0 0
queue 1 309232345 450 0
queue 2 300 10 0
queue 3 91 0 0
Repeating this command results in the counters incrementing for queue 1 threshold 1. What are two options for reducing the packet loss on this interface while preserving the end-to-end DSCP marking? (Choose two)

Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue

Increase the buffer allocation for input queue 1

Increase the buffer allocation for output queue 1

Alter the service policy to police to a higher CIR

Change the egress queue map on L2SW4 to map this traffic to a less congested queue

Page: 1 / 7

Total 87 questions Full Exam Access