20 October, 2019

[Oct-2019-20] Up To The Immediate Present 300-180 Guidance

Our pass rate is high to 98.9% and the similarity percentage between our 300-180 study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco 300-180 exam in just one try? I am currently studying for the Cisco 300-180 exam. Latest Cisco 300-180 Test exam practice questions and answers, Try Cisco 300-180 Brain Dumps First.

Page: 1 / 22

Total 269 questions Full Exam Access

Question 1

Refer to the exhibit.
300-180 dumps exhibit

You have fabric interconnects. You discover that all traffic flows through a fabric interconnect named fabric-interconnect B.
Which of the following could cause the issue?

An administrator evacuated fabric-interconnect A.

There is a version mismatch between the fabric interconnects.

An administrator assigned an invalid OOBP IP address to fabric-interconnect B.

the fabric interconnects have duplicate IP address.

Question 2

Refer to the exhibit.
300-180 dumps exhibit

No OSPF neighborship exists between N5K-1 and N7K-1. Which configuration resolves this issue?

(config)# router ospf 1(config-router)# network 192.168.103.152 255.255.255.252 area 0

(config)# ip router ospf 1 area 0

(config)# router ospf 1(config-router)# network 192.168.103.152 0.0.0.3 area 0

(config-rf)# ip router ospf 1 area 0

Question 3

Refer to the exhibit.
300-180 dumps exhibit

Your customer is migrating their existing top-of-rack data center to a new location that uses an end-of-rack configuration. The customer requests a site survey prior to the migration.
Which fact must you highlight in your survey that is required for a successful translation?

power source must be 240 volts only for blade chassis.

power source must be 240 volts only for fabric interconnect switches.

blade chassis using passive TWNAX cables must be placed within 5 meters of the end rack.

Blade chassis must not be fully equipped with blades when using and end-of-racksetup.

Question 4

You have three VDCs named VDCI, VDC2 and VDC3 connected to the same environment, Due to a network device malfunction, there is an ARP storm in VDC1 Users in VDC2 discover that
ARP is not resolving in VDC1. What is causing the issue?

The committed information rate is exceeded.

VDC1 is responsible for processing ARP for all of the VDCs,

The CoPP settings for VDC1 are Incorrect.

The CoPP settings for VDC2 are incorrect,

Question 5

Refer to the exhibit. After a boot policy is added, the profile stops working, which option is a possible cause of the issue?
300-180 dumps exhibit

An iSCSI adapter is being on top of the vNIC

Both of the adapters from the fabric A and fabric B must be specified

The name of the adapter is incorrect

The boot target does not exist

Question 6

What is one requirement for running FabricPath on a Cisco Nexus 7000 Series switches?

You must have an F Series module

You must run NX-OS version 4.2 to run FabrciPath

ISSU needs to be disabled to run FabricPath

LAN_TRANSPORT_SERVICES_PKG license needs to be installed to run FabrciPath

Question 7

Refer to the exhibit.
You are configuring a FCoE VDC on a Cisco Nexus 7000 Series Switch. You are required to identity compatible QoS policies for the FCoE VDC. Drag and drop the QoS policy names on the left to their correct compatibility categories on the right.
300-180 dumps exhibit

Solution:
300-180 dumps exhibit

Does this meet the goal?

Yes

Question 8

A customer has a Cisco UCS Center cluster. The customer configures LDAP as the AAA protocol and enables SSL for LDAP. The LDAP authentication fails. Which issue is the cause of the failure?

The LDAP client passed an incorrect from the trustpoint.

The CA certificate is missing from the trustpoints.

The LDAP server limit that is set by an administrative authority was exceeded.

The LDAP time limit that is specified by either the client or the server was exceeded.

Question 9

Which CLI command identifies the service profile that is associated with a particular compute blade, VIF, vNIC type, link state, and pinned interface?

show service-profile path server 1/2

show service-profile circuit server 1/2

show server-blade circuit server 1/2

show server-blade path server 1/2

Question 10

Refer to the exhibit.
300-180 dumps exhibit

Which action removes the system designation from VLAN 70?

Create another port profile that excludes VLAN 70

Shut down the port profile first

Delete the uplink-storage port profile, and then receive it

Remove VLAN 70 from the trunk first

Question 11

In order to fulfill the requirement to prevent the creation of end-to-end loops across a multihomed OTV network that connects two different data centers, what is the solution to this problem?

prioritize the transmission of STP BPDUs across the overlay

design the DCI connectivity as a hub and spoke

define a conservative TTL for all packets traversing the OTV network

enable AED on a per-VLAN basis between each OTV edge device with the same site ID

Question 12

Which option is exchanged between neighbors during OTV adjacency formation across the Layer 3 multicast network?

IGMP packets

OTV open messages

L1 IS-IS Hello packets

OTV adjacency packets

Question 13

Refer to the exhibit.
300-180 dumps exhibit

VSAN traffic is not being routed through SAN fabric. Which action is helpful to resolve the problem?

Make sure that the FSPF hello interval value matches on both switches.

Change the FSPF hello timer back to the default of 5 seconds.

Make sure that the FSPF hello timers are different so that they do not compete.

Make sure that the FSPF dead timers are both set to 0.

Question 14

Refer to the exhibit. You discover that eth1/1 stopped forwarding data. Which option describes how to resolve the issue?
300-180 dumps exhibit

Reboot the switch.

On the adjacent switch, run the spanning-tree port type network command.

On the switch, change the STP type.

On the adjacent switch, disable bridge assurance.

Question 15

Refer to the exhibit.
300-180 dumps exhibit

DC-SWITCH 14 is a Cisco Nexus switch Port channel 1106 connects to a Cisco Nexus switch named DC-SWITCH10. Which cause of the I flag is likely?

Port channel 1106 is administratively down.

STP is blocking port channel 1106

LACP is misconfigured on DC-SWITCH14

LACP is misconfigured on DC-SWITCH10.

Question 16

Refer to the exhibit.
300-180 dumps exhibit

A customer is having problems with NPV. Which of these is the cause of the problem?

No server was requested or received by the FLOGI database.

One external link must be up for server interface to be up.

Internal links are down and must be up for the server interface to be up.

VSANs are misconfigured on the upstream ports.

VLANs are misconfigured on the upstream ports.

Question 17

A customer is troubleshooting FCoE in its network. They have discovered that vFC is currently down and there is no active STP port state on the bound Ethernet interface. What should the STP port state be to correct this issue?

The bound interface should be in an STP forwarding state for the native VLAN only.

The bound interface should be in an STP learning state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.

The bound interface should be in an STP forwarding state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.

The bound interface should be in an STP blocking state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.

Question 18

A customer calls you to report that it receives an error when entering the pinning max-links 4 command in FEX configuration mode on its Cisco Nexus 5596T Switch. Which of these is a likely cause for this condition?

The FEX fabric interface is down.

The transceiver is incorrect.

A fabric interface is in a port channel.

The fabric interface switchport mode is set to Access.

Only two fabric interfaces are connected.

Question 19

You are troubleshooting LACP issues on a Cisco Nexus platform. Which two LACP modes can you view by using the show lacp interface command? (Choose two.)

passive

active

standby

auto-negotiate

Question 20

Which three of these would cause two switch fabrics not to merge? (Choose three.)

Two or more switches do not have at least one assigned domain ID in common.

Two switches have different assigned VSANs on the connecting ports.

Two switches have different assigned VLANs on the connecting ports.

The static domain ID does not override the dynamic ID.

The election of the static domain is only determined by the WWNs of the two switches.

The physical connectivity between the two switches is not active.

Question 21

Refer to the exhibit.
300-180 dumps exhibit

You configure a vPC between two Cisco Nexus 7000 Series switches but the peer link will not come up. What is the problem?

The configuration is correc

The problem lies elsewhere.

The vPC domain numbers must be different.

The role priority must be the same.

The system priority must be the same.

Question 22

After removing a VMM domain from an EPG, you discover that the associated virtual port groups remain in the VMware vCenter configuration. What causes the virtual port groups to persist in the configuration?

The MAC addresses that are learned by the ports of the spine switches are incorrect.

The port groups are being used by a virtual machine network adapter.

The MAC addresses that are learned by the ports of the leaf switches are incorrect

There is a mismatch between the data center name in vCenter and the VMM controller policy.

Question 23

Refer to the exhibit.
300-180 dumps exhibit

The server port connected to the NPV edge switch does not come online. Which action should fix the problem?

Move the NP ports on the NPV edge and the F ports on the NPIV into the same VSAN 99.

Move the NP ports on the NPV edge and the F ports on the NPIV in the default VSAN 1.

Move all the ports into VLAN 1.

Move all the ports into VSAN 99.

Move all the ports into VLAN 99.

Question 24

Refer to the exhibit.
300-180 dumps exhibit

IGMP Snooping is configured on the Cisco Nexus 1000v switch to support the P1M sparse mode implementation within the data center. Which command validates the multicast configuration below on the Nexus 1000v switch?
300-180 dumps exhibit

show ip igmp snooping groups vlan 702

show ip igmp snooping groups vlan 700

show ip igmp snooping groups vlan 703

show ip igmp snooping groups vian 701

Question 25

An engineer enters the show svs neighbors command as shown below. Which statement describes the output of the command?
300-180 dumps exhibit

The VSM cannot connect to the VEM.

The vCenter server cannot connect to the VSM.

The VSM is connected to the VEM by using an Layer 2 network.

The VSM is connected to the VEM by using an Layer 3 network.

Question 26

A customer is deploying multihop FCoE in its network. Which guideline must the customer follow with respect to VE ports to make this deployment possible?

Auto mode on the vFC interface is supported.

VE-port trunking is supported over FCoE-enabled VLANs.

VE-port interface binding to MAC addresses is supported.

A VE port is disabled for trunk mode by default.

Question 27

Two fabric interconnects fail during a Cisco UCS firmware upgrade. Drag and drop the recovery steps from the left into the correct order on the right.
300-180 dumps exhibit

Solution:
300-180 dumps exhibit

Does this meet the goal?

Yes

Question 28

Refer to the exhibit.
300-180 dumps exhibit

VM-1 and VM-3 are in different EPGs but in the same BD. Which statement about the communication between VM-1 and VM-3 is true?

The packet must transverse a Layer 3 interface.

The flow uses unencapsulated VLANs

The flow must transverse the spine.

The flow stays local to the leaf switch

Question 29

You see incoming updates in the logs from the hypervisor. But the State Of the Cisco APIC fails to change
Which option is a possible cause Of the issue?

VMM is not integrated properly

The APIC is in a minority state

No uplinks are configured on the Cisco AVS.

The VMM credentials are incorrect.

Question 30

If no traffic was ever sent across the overlay, what will the show mac address-table command on the OTV VDC indicate?

invalid command

the MAC address of the local OTV join interface

the system IDs of all the local OTV edge devices

the system IDs of all the local and remote edge devices in the overlay

all the MAC addresses learned on the extended VLAN

Page: 1 / 22

Total 269 questions Full Exam Access