22 October, 2019

Realistic ISTQB CTFL-Foundation Discount Pack

Proper study guides for Renovate ISTQB Certified Tester Foundation Level certified begins with ISTQB CTFL-Foundation preparation products which designed to deliver the High value CTFL-Foundation questions by making you pass the CTFL-Foundation test at your first time. Try the free CTFL-Foundation demo right now.

Page: 1 / 28

Total 338 questions Full Exam Access

Question 1

Pick the best definition of quality:

Quality is job one

Zero defects

Conformance to requirements

Work as designed

Question 2

Which of the following test design techniques is not a black box technique?

Equivalence partitioning

State transition testing

Boundary value analysis

Statement coverage

Question 3

Which of the following BEST defines static techniques? [K1]

Executing the software work product

Manually examining the code or project documentation

Automated analysis of the code or project documentation

Manual examination and automated analysis of code or project documentation

Question 4

Independent Verification & Validation is:

Done by the Developer

Done by the Test Engineers

Done By Management

Done by an Entity Outside the Project’s sphere of influence

Question 5

Consider the following pseudo code
1. Begin
2. Read Gender
3. Print “Dear”
4. If Gender = ‘female’
5. Print (“Ms”)
6. Else
7. Print ( “Mr”)
8. Endif
9. End
How many test cases are needed to achieve 100 per cent decision coverage?

Question 6

In the above State Table, which of the following represents an invalid transition?
CTFL-Foundation dumps exhibit

Event C from S3

Event E from S4

Event B from S2

Event D from S4

Question 8

In general, why is it NOT a good idea to estimate the testing effort based only on a percentage of development effort? Identify THREE valid reasons. 1 credit

The quality of the development estimate may be poor.

In general bottom-up estimation is always better than top-down estimation.

The percentage based technique only applies to the V life cycle model.

Using the same percentage every time does not address the level of risk of the application to be tested.

The maturity of the organization, e.

the quality of the test basis, quality of development testing, configuration management, availability of test tools, also influence the effort needed for testing.

It builds on large set of historical data

The result is almost always a too low estimate for the required test effort

Question 9

Which of the following is the main purpose of the component build and integration strategy?

to ensure that all of the small components are tested

to ensure that the system interfaces to other systems and networks

to ensure that the integration testing can be performed by a small team

to specify how the software should be divided into components

to specify which components to combine when, and how many at once

Question 10

Which of the following statements are true?
(i) Defects are likely to be found earlier in the development process by using reviews rather than static analysis.
(ii) Walkthroughs require code but static analysis does not require code.
(iii) Informal reviews can be performed on code and specifications.
(iv) Dynamic techniques are generally used before static techniques.
(v) Dynamic techniques can only be used after code is ready to be executed.

(i), (ii), (vi).

(ii), (iii), (v).

(i), (iv), (v).

(i), (iii), (v).

Question 11

A software component has the code shown below: Program BiggestA,
Biggest: Integer Begin
Read A Biggest = 10 While A > 0 Do
If A > Biggest Then Biggest = A Endif
Read A Enddo End
The component has exit criteria for component testing that include 100% statement coverage. Which of the following test cases will satisfy this criterion?

10, 0

10, 5, 0

10, 11, 0

Question 12

The five parts of the fundamental test process have a broad chronological order. Which of the options gives three different parts in the correct order?

Implementation and execution, planning and control, analysis and design.

Analysis and design, evaluating exit criteria and reporting, test closure activities.

Evaluating exit criteria and reporting, implementation and execution, analysis and design.

Evaluating exit criteria and reporting, test closure activities, analysis and design.

Question 13

Which of the following would you expect to see in the master test plan? 1 credit

A description of how the test cases are cross-referenced to requirements in the test management tool.

A detailed identification of the resources that will carry out structural testing in the first iteration.

The test approach that will be applied at system integration testing.

A list of the names of the testers who will carry out the performance testing for the final iteratio

Question 14

Tests are prioritized so that:

You shorten the time required for testing

You do the best testing in the time available

You do more effective testing

You find more faults

Question 15

You are examining a document which gives the precise steps needed in order to execute a test. What is the correct definition of this document?

Test design specification

Test condition

Test procedure specification

Test case specification

Question 16

Consider the typical objectives of testing. Which of the following metrics can be used to measure the effectiveness of the testing process in achieving one of those objectives? 1 credit

Average number of days between defect discovery and resolution

Percentage of requirements covered

Lines of code written per developer per day

Percentage of test effort spent on regression testing

Question 17

Which of the following is not true of regression testing?

It can be carried out at each stage of the life cycle.

It serves to demonstrate that the changed software works as intended.

It serves to demonstrate that software has not been unintentionally changed.

It is often automated.

Question 18

Maintenance testing is:

updating tests when the software has changed

testing a released system that has been changed

testing by users to ensure that the system meets a business need

testing to maintain business advantage

Question 19

Which of the following is a valid reason for writing test cases based on experience and intuition? [K1]

Use of formal techniques requires expensive training

Only experience can ensure all functionality is covered

Tests based on experience and intuition can supplement formal techniques

Formal techniques require the use of expensive tools

Question 20

An input field takes the year of birth between 1900 and 2004. The boundary values for testing this field are:

0,1900,2004,2005

1900, 2004

1899,1900,2004,2005

1899, 1900, 1901,2003,2004,2005

Question 21

Which of the following is the task of a Tester?

Interaction with the Test Tool Vendor to identify best ways to leverage test tool on the project.i

Prepare and acquire Test Dataii

Implement Tests on all test levels, execute and log the tests.i

Create the Test Specifications

i, ii, iii is true and iv is false

ii, iii, iv is true and i is false

i is true and ii, iii, iv are false

iii and iv is correct and i and ii are Incorrect

Question 22

Which is not in sequence in 11 Step Software Testing process..?

Assess development plan and status

Develop the test plan

Test software design

Test software requirement

Question 23

Which of the following terms is used to describe the management of software components comprising an integrated system?

Configuration management

Incident management

Test monitoring

Risk management

Question 24

Which of the following are static techniques?

Walkthrough.

State transition testing.

Decision table testing.

Statement testing.

Question 25

Which of the following would be the TWO most appropriate examples of entry criteria documented in the system integration test plan? 2 credits

The percentage of decision coverage achieved during unit testing.

The availability of the latest version of the capture-replay tool (for testing the interface with the newly developed test management tool).

The sign-off of a performance test software release note (test item transmittal report) by both development and testing showing that system performance meets the specified acceptance criteria.

The percentage of acceptance test procedures scheduled for execution.

The percentage of requirements coverage achieved during system integration tes

Page: 1 / 28

Total 338 questions Full Exam Access