02 January, 2024

Renewal Service Provider Routing And Switching Specialist (JNCIS-SP) JN0-363 Answers

we provide Printable Juniper JN0-363 download which are the best for clearing JN0-363 test, and to get certified by Juniper Service Provider Routing and Switching Specialist (JNCIS-SP). The JN0-363 Questions & Answers covers all the knowledge points of the real JN0-363 exam. Crack your Juniper JN0-363 Exam with latest dumps, guaranteed!

Page: 1 / 5

Total 65 questions Full Exam Access

Question 1

Exhibit

Referring to the exhibit, which two statements are correct? (Choose two.)

The OSPF Interfaces are configured as point-to-point.

The ge-0/0'1.0 Interface is configured as passive.

The R2 device is an ABR.

Junos OS default OSPF hello timers and dead intervals are used on all interfaces.

Question 2

Exhibit

You are asked to configure the OSPF environment to prevent the DRother routers from participating in DR/BDR election.
Referring to the exhibit, which command will accomplish this task?

set protocols ospf area 0.0.0.0 interface ge-0/0/l priority 255

set protocols ospf area 0.0.0.0 interface ge-0/0/1 priority 0

set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type nbma

set protocols ospf area 0.0.0.0 interface ge—0/0/1 interface-type p2p

Question 3

Exhibit

You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command.
Referring to the exhibit, what is the problem?

The command is only available if non-stop routing is enabled.

The command is only available on the backup Routing Engine.

The command is only available If a backup router is configured.

The command is only available If graceful restart is enabled.

Question 4

Interface ge-0/0/0.0 connecls yout network to your ISP. You want to advertise this interface address as an Internal route In OSPF without creating a neighbor with your ISP.
In this scenario, how is this task accomplished?

Remove interface ge-0/0/0.0 from OSPF.

Create a generated route for Interface ge-0/0/0.0.

Add ge-0/0/0.0 as a passive interface In OSPF.

Configure a static route for Interface ge-0/0/0.0.

Question 5

Exhibit

Which type of load balancing is shown in the exhibit?

elastic load balancing

per-packet load balancing

per-flow load balancing

network load balancing

Question 6

You are asked to create connections between routing instances on the same Junos device and route between the connected Instances. What are two ways to accomplish this task? (Choose two.)

Use physical interfaces.

Use an IRB interface.

Use logical tunnel interfaces.

Use loopback interfaces.

Question 7

Exhibit

You want the R1 and R3 routers to forward traffic destined to the 203.0.113.0/24 network through R2. Which BGP attribute would you modify to satisfy this requirement?

community

origin

MED

local preference

Question 8

Which two statements ate correct about the BGP next-hop attribute value? (Choose two.)

By default, the next-hop value is changed across IBGP links.

By default, the next-hop value is changed across EBGP links.

By default, the next-hop value is not changed across IBGP links.

By default, the next-hop value is not changed across EBGP links.

Question 9

You are asked to configure an LSP which uses the OSPF link state database for path computations. Which two statements are correct in this scenario? (Choose two.)

You must use the no-cspf parameter in the label-switched-path configuration.

Traffic engineering extensions ate enabled by default In OSPF.

Traffic engineering extensions are not enabled by default in OSPF.

You must use the policing parameter in the label-switched-path configuration.

Question 10

What are two types of SlDs used in segment touting? (Choose two.)

node

adjacency

link

interface

Question 11

What are three types of MPLS routers? (Choose three.)

transit routers

peering routers

egress routers

aggregation routers

ingress routers

Question 12

Which new field is added to an IPv6 header as compared lo IPv4?

version

checksum

fragment offset

flow label

Question 13

You want to enable a routing platform with redundant REs to switch from a primary RE to a backup RE without alerting peer nodes. Which two technologies would you use to satisfy this requirement? (Choose two.)

GRES

VRRP

NSR

ISSU

Question 14

You are deploying link aggregation groups.

By default, what are two considerations in this scenario? (Choose two.)

There should only be four member links per LAG.

All the ports must have the same speed.

Member links are required to be contiguous ports.

Member links can reside on different members within an MC-LAG.

Question 15

You want to see a detailed list of all established BGP sessions. In this scenario, what would be a valid command to accomplish this task?

show bgp neighbor

show bgp summary

show rouse receive-protocol bgp

show rouse protocol bgp

Page: 1 / 5

Total 65 questions Full Exam Access