16 October, 2019

Simulation HP HPE6-A45 Samples

It is impossible to pass HP HPE6-A45 exam without any help in the short term. Come to Testking soon and find the most advanced, correct and guaranteed HP HPE6-A45 practice questions. You will get a surprising result by our Far out Implementing Aruba Campus Switching Solutions Exam practice guides.

Page: 1 / 9

Total 115 questions Full Exam Access

Question 1

A network administrator configures DHCP snooping on VLAN 2. How does the switch handle DHCP traffic that arrives in this VLAN on an untrusted interface?

It accepts packets from a DHCP server, but drops client packets.

It drops all DHCP traffic and logs a security event.

It accepts both client and server packets as long as they match the DHCP binding table.

It accepts client packets, but drops packets from a DHCP serve

Question 2

A network administrator enters this command: Switch(config)# aaa authorization user-role enable How does this affect device authentication?

The local manager and operator accounts will no longer work unless they are associated with a user role on the switch.

Authenticated devices must receive their dynamic settings, such as VLAN ID and ACLs, from the RADIUS server Access-Accept.

Authenticated devices will be defined proper access if the RADIUS server sends any VSA except the user role VSA

Role-based mode will no longer be available with tunneled node to prevent conflicts with the AAA user role

Question 3

An AOS-Switch needs to be configured to support tunneled node in role-based mode. The Mobility Controller administrators tell the switch administrators that the AOS-Switch will integrate with a cluster of Mobility Controllers. The cluster virtual IP address is 10.1.1.10.
How should switch administrator integrate the AOS-Switch with the cluster?

Double-check the settings with the Mobility Controller administrators because the planned configuration is incomplete with the switch settings.

Configure the virtual IP address as the tunneled-node-server address, tunneled node will work, but the clustering features will not provide redundancy.

Configure the virtual IP address as the tunneled-node-server addres

The switch will automatically learn controller IP addresses to which to tunnel various traffic.

Configure the virtual IP address for the primary tunneled-node-server and an actual controller IP address for the backup tunneled-node-server in order to receive redundancy.

Question 4

Network administrators want to gain insight into network utilization, traffic patterns, and the types of applications in use across the network over the long term.
Which technology can help them achieve this goal?

RMON

sFlow

SNMP traps

DiffServ

Question 5

Two AOS-Switches are directly interconnected. The network administrator wants to prevent broadcast storms and other Layer 2 issues that could occur if there is physical damage to a cable.
Which technology should the administrator implement on the connected switch interfaces?

MAC Lockdown

Bidirectional Forwarding Detection (BFD)

Spanning Tree Root Guard

Unidirectional Link Detection (UDLD)

Question 6

A company wants to implement 802.1X authentication to authenticate client devices on AOS-Switch ports. The company has a RADIUS server that uses PEAP MSCHAP-v2 for the authentication method. What is one task administrators should complete before they implement the plan?

Set up an isolated VLAN in the network for the 802.1X communications.

Install personal certificates on client devices.

Configure DHCP services on the AOS-Switches for pre-authenticated clients.

Ensure client devices trust the RADIUS server certificat

Question 7

A company has AOS-Switches, Aruba ClearPass, and Aruba AirWave. A network administrator needs to set up a new switch with the same settings found on other switches in the company.
Which action is likely to be the most useful to perform the task?

View usage patterns on the switches on AirWave.

Retrieve the running config from ClearPass.

Use the configuration audit tool on AirWave.

Access the Network Device view on ClearPas

Question 8

Refer to the exhibit.
HPE6-A45 dumps exhibit

A network administrator needs to deploy AOS-Switches that implement port-based tunneled node. Their Aruba controller has IP address 10.1.10.5/24. The architect has assigned tunneled-node endpoints to VLAN 20.
What is one issue with the current configuration planned for VLAN 20 on the switch?

VLAN 20 must have GRE enabled on it.

VLAN 20 cannot have an IP address.

VLAN 20 must have an IP address in the same subnet as the controller.

VLAN 20 must not enable jumbo frame

Question 9

A network administrator needs to configure an AOS-Switch to classify traffic. Comparing QoS policy and global policy, what is one function that only a class-based QoS policy can fulfill?

Apply a DSCP to HTTP traffic from some sources but not other sources.

Apply a DSCP rather than an 802.1p value to classified traffic.

Override the incoming DSCP in the received traffic.

Override the DSCP or priority applied directly to an interfac

Question 10

A network administrator needs to create a backplane stack with four AOS-Switches. The administrator wants to choose which switch becomes the commander. Which procedure meets those needs?

Boot all of the switches at the same time and then connect the backplane stacking link

Then, access the desired commander, and make sure it has member ID 1.

Configure backplane switches settings on each switch while disconnecte

Make sure the desired commander has priority value 1. Then, connect the switches.

Boot up the desired commander first and make sure stacking is enabled on i

Then, connect the stacking links and boot the other switches.

Configure backplane switching settings on each switch while disconnecte

Make sure the desired commander has member ID 1. Then, connect the switches.

Question 11

Refer to the exhibit.
HPE6-A45 dumps exhibit

An AOS-Switch connects to an unmanaged switch in a meeting room. The exhibit shows security settings for this port. Users report that they sometimes lose connectivity and then get it back.
Which best practice should network administrators follow to avoid issue?

The loop protection and port security actions should be set to match.

Eavesdrop prevention should be disabled when report security is in limited-continuous mode.

Port security and loop protection should not be enabled on the same port.

Loop protection should operate in VLAN mode, rather than port mode, when port security is enable

Question 12

Refer to the exhibit.
HPE6-A45 dumps exhibit

AOS-Switches will enforce 802.1X authentication on edge ports. The company has two RADIUS servers, which are meant to provide redundancy and load sharing of requests. The exhibit shows the planned RADIUS settings to deploy to the switches.
What should customers understand about this plan?

AOS switches do not support two RADIUS servers for redundancy, instead, a secondary authentication method is required.

Dynamic authentication is only permitted on one of the RADIUS servers and must be removed from the other.

Each RADIUS server must use a unique port number for the authentication and dynamic authorization port.

Each AOS-Switch will send all RADIUS requests to the first server on the list unless that server becomes unreachabl

Question 13

An administrator wants to ensure that an AOS-Switch forwards all traffic that it receives on interface 1 with high priority.
- Switches should also communicate the high priority to other switches across the traffic path.
- The switch has type of service disabled.
- The administrator plans to apply 802.1p priority 5 to interface 1.
What should the administrator check to ensure that the configuration will work properly?

Interface 1 receives traffic with a tag.

The AOS-Switch is configured to use eight queues.

The forwarding path for the traffic uses VLAN tags.

An 802.1p-to-DSCP map exists for priority 5.

Question 14

A company has AOS-Switches deployed at sites with inexperienced IT staff. The main office network administrators want to track if configurations change on branch switches.
What should be set up for this purpose?

an SNMP trap

an RMON alarm

an IP SLA profile

an auto-config server

Question 15

The security policy for a company requires that switches use SNMPv3 and accept all read-only SNMPv2c messages. The network administrator enables SNMPv3. Which additional action should the network administrator take to comply with this policy?

Disabled SNMPv3 inform timeouts.

Enable SNMPv3 only operation.

Enable SNMPv3 restricted mode.

Disable SNMPv1/v2

Question 16

Two AOS-Switches connect on VLAN 10 in OSPF Area 1, which is defined as a stub area on both. Which mismatch can cause OSPF routers to lose adjacency?

The administrator adds the backbone area to just one of the routers.

The administrator enables graceful restart, or nonstop switching, on just one of the routers.

The administrator enables jumbo frames on VLAN 10 on just one of the routers.

The administrator adds the no-summary option to Area 1 on just one of the router

Question 17

A network administrator can set the OSPF metric type on an AOS-Switch to Type 1 or Type 2. What is the difference?

A Type 2 metric marks external routes that can be advertised in NSSAs, while a Type 1 metric marks external routes that can only be advertised in normal areas.

A Type 2 metric assigns cost to a 100 Gbps link, while a Type 1 metric assigns cost 1 to all links Mbps or higher.

A Type 2 metric is assigned to multiple external routes that are aggregated together, while a Type 1 metric does not permit external route aggregation.

A Type 2 metric stays the same as the external route is advertised, while a Type 1 metric increments with internal OSPF link costs.

Question 18

A company deploys AOS-Switches at sites with inexperienced IT staff. The main office network administrators want to monitor thresholds to generate alerts on branch switches. What should be set up for this purpose?

an SNMP trap

an RMON alarm

an auto-config server

an sFlow instance

Question 19

Refer to the exhibits.
Exhibit 1
HPE6-A45 dumps exhibit

Exhibit 2

A network administrator wants to set up mirroring of traffic from port 1 on Switch-1 to port 1 on Switch-2. Exhibit-2 shows the commands that the administrator enters. The mirroring does not work correctly.
What must the administrator do to correct the error?

Change the port ID on Switch 1 to 50001, so that it is unique from the port ID on Switch-2.

Re-configure the mirror endpoint command on Switch-2 with the IP addresses reversed in order.

Remove the commands and re-enter them on Switch-1 first and then on Switch-2.

Specify the mirror endpoint command in Switch-1 and the mirror 1 remote-ip command on Switch-2.

Question 20

Refer to the exhibit.
HPE6-A45 dumps exhibit

Switch-2, Switch-5, and Switch-6 currently have many OSPF routes to Area 1 networks. The network administrator wants to replace these routes with a single aggregated route to 10.1.0.0/16 on each switch. Where should the administrator specify the 10.1.0.0/16 range?

in the Switch-2 OSPF Area 2 configuration

in the Switch-1 OSPF Area 0 configuration

in the Switch-1 OSPF Area 1 configuration

in the Switch-2, Switch-5, and Switch-6 OSPF global configuration

Question 21

Refer to the exhibits.
Exhibit 1
HPE6-A45 dumps exhibit

Exhibit 2

Exhibit 1 shows a portion of the BGP routing table when the BGP solution was first deployed. Exhibit 2 shows the same portion at the current time. What can explain the current state?

Due to changes in the private network, Switch-1 can no longer reach 192.168.2.1.

Switch-1 can no longer reach ISP 1 at 192.168.1.1.

Due to changes at ISP 1, Switch-1 now selects a different best route.

An administrator has applied a route map on Switch-1 that filters advertised route

Page: 1 / 9

Total 115 questions Full Exam Access