04 July, 2020

Tested Cisco 350-501 Exam Dumps Online

Want to know Pass4sure 350-501 Exam practice test features? Want to lear more about Cisco Implementing and Operating Cisco Service Provider Network Core Technologies certification experience? Study Validated Cisco 350-501 answers to Far out 350-501 questions at Pass4sure. Gat a success with an absolute guarantee to pass Cisco 350-501 (Implementing and Operating Cisco Service Provider Network Core Technologies) test on your first attempt.

Free demo questions for Cisco 350-501 Exam Dumps Below:

Page: 1 / 8

Total 102 questions Full Exam Access

Question 1

Which BGP attribute is used first when determining the best path?

origin

AS path

local preference

weight

Question 2

Which two uses of the YANG data modeling language are true? (Choose two.)

It can be used to model the configuration used by NETCONF operations.

It can be used to access a device by HTTP.

It can be used to replace the OSI model for troubleshooting.

It can be used to shape state data of network elements.

It can be used to replace RESTCONF as a mechanism to install and manipulate configuration.

Question 3

A router RP is configured to perform MPLS LDP graceful restart.
Which three steps are included when the RP sends an LDP initialization message to a neighbor to establish an LDP session? (Choose three.)

Learn from Neighbor (N) flag, set to 1

Recovery Time field

Type-9 LSA

Reconnect Timeout field

Graceful restart capability in OPEN message

Learn from Network (L) flag, set to 1

Question 4

Why do packet loops occur during the configuration of BIDIR-PIM?

The network does not support BIDIR-PIM.

The network is partially upgraded to support BIDIR-PIM.

The router has not been configured to advertise itself.

No interface for carrying traffic for multicast groups has been configured.

Question 5

Refer to the exhibit. Assume all other configurations are correct and the network is otherwise operating normally. Which conclusion can you draw about the neighbor relationship between routers R1 and R2?

The neighbor relationship is up.

The neighbor relationship will be up only if the two devices have activated the correct neighbor relationships under the IPv4 address family.

The neighbor is down because the local-as value for R2 is missing in the R1 neighbor statement.

The neighbor relationship is down because R1 believes R2 is in AS 65012.

Question 6

Which service is a VNF role?

Network

Firewall

Storage

Compute

Question 7

Which configuration mode do you use to apply the mpls ldp graceful-restart command in IOS XE Software?

MPLS LDP neighbor

interface

MPLS

global

Question 8

Refer to the exhibit. BGPsec is implemented on R1, R2, R3, and R4. BGP peering is established between neighboring autonomous systems. Which statement about implementation is true?

BGP updates from the iBGP peers are appended with a community of local-as.

BGP updates from the all BGP peers are appended with a community of no-export.

BGP updates from the eBGP peers are appended with an additional AS path value that is statically set by the domain administrator.

BGP updates from the eBGP peers are appended with a BGPsec attribute sequence that includes a public key hash and digital signature.

Question 9

While implementing TTL security, you issue the PE(config-router-af)#neighbor 2.2.2.2 ttl-security hops 2 command.
After you issue this command, which BGP packets does the PE accept?

to 2.2.2.2, with a TTL of 2 or more

from 2.2.2.2, with a TTL of less than 2

to 2.2.2.2, with a TTL of less than 253

from 2.2.2.2, with a TTL of 253 or more

Question 10

Refer to the exhibit. With which router does IOSXRV-1 have LDP session protection capability enabled but session hold up is not active?

192.168.0.4

192.168.0.5

192.168.0.1

192.168.0.3

Question 11

Refer to the exhibit. Which statement about the neighbor statements for 192.168.1.1 is true?

The router sends BGP labels for its prefixes to this peer.

The router must have TDP configured for the send-label command to operate.

The neighbor router receives at least four labels from this router.

The router sends only a label for the prefix for Loopback0.

Question 12

You are writing an RPL script to accept routes only from certain autonomous systems. Consider this code:
RP/0/RP0/CPU0:router(config-rpl)# if as-path in (ios-regex ‘.*77$’) RP/0/RP0/CPU0:router(config-rpl-if)# pass RP/0/RP0/CPU0:router(config-rpl-if)# endif
If you apply this code to BGP filters, which effect does the code have on your router?

denies routes from AS 7070

allows routes from AS 7077

denies routes from AS 7007

allows routes from AS 770

Question 13

Refer to the exhibit. In which way does router R1 operate differently than router R2?

R1 sends LSA types 5 and 7, while R2 sends type 1, 2, and 7 LSAs.

R1 sends LSA type 2 only, while R2 sends type 1 and type 7 LSAs.

R1 sends LSA type 2 only and R2 sends LSA type 1 only.

R1 sends LSA types 1 and 2, while R2 sends type 1,2, and 7 LSAs.

Question 14

Which task must be performed first to implement BFD in an IS-IS environment?

Configure BFD in an interface configuration mode.

Disable Cisco Express Forwarding on all interfaces running routing protocols other than IS-IS.

Configure all IS-IS routers as Level 2 devices.

Configure BFD under the IS-IS process.

Question 15

Refer to the exhibit. This output is included at the end of an output that was provided by a device using NETCONF. What does the code show?

It shows that the full configuration is being modeled by YANG.

It shows NETCONF uses remote procedure calls.

It shows the hostname of the device as rpc-reply.

It shows that the running configuration is blank.

Question 16

Refer to the exhibit. You are configuring an administrative domain in the given multi-vendor environment with PIM-SM. Which feature can you implement so that devices can dynamically learn the RP?

BSR

BIDIP-PIM

Auto-RP

SSM

Question 17

Refer to the exhibits. Which information is provided for traceback analysis when this configuration is applied?

source interface

packet size distribution

IP sub flow cache

BGP version

Question 18

A regional MPLS VPN provider operates in two regions and wants to provide MPLS L3VPN service for a customer with two sites in these separate locations. The VPN provider approaches another organization to provide backbone carrier services so that the provider can connect to these two locations.
Which statement about this scenario is true?

When edge routers at different regional sites are connected over the global carrier backbone, MP-eBGP must run between the routers to exchange the customer VPNv4 routes.

When eBGP is used for label exchange using the send-label option, MPLS-BGP forwarding is configured under the global ABC CSC PE-to-CE interface.

When BGP is used for both route and label exchange, the neighbor a.b.c.d send-label command is used under the address-family VPNv4 command mode.

When IGP is used for route exchange and LDP for label exchange, MPLS is enabled only on the VRF interface on the backbone-carrier PE side.

Question 19

Which regular expression query modifier function indicates the start of a string?

[^]

Question 20

Refer to the exhibit. A network administrator wants to enhance the security for SNMP for this configuration. Which action can the network administrator implement?

Add a community string to the existing entry.

Maintain the configuration but switch to an encrypted password for device access through SSH.

Re-configure to use SNMPv2 with MD5 authentication.

Re-configure to use SNMPv3.

Question 21

Refer to the exhibit. A network engineer is configuring customer edge routers to finalize a L2VPN over MPLS deployment. Assume that the AToM L2VPN service that connects the two CEs is configured correctly on the service provider network.
Which action causes the solution to fail?

OSPF does not work with L2VPN services.

The routing protocol network types are not compatible.

A loopback with a /32 IP address has not been used.

The xconnect statement has not been defined.

Question 22

Which configuration modifies Local Packet Transport Services hardware policies?

$\"350-501$

Question 23

Refer to the exhibit. After implementing a new design for the network, a technician reviews the pictures CLI output as part of the MOP. Which two elements describe what the technician can ascertain from the ImpNull output? (Choose two.)

Ultimate Hop Popping is in use for the prefix displayed.

Penultimate Hop Popping is in use for the prefix displayed.

Label 0 is used for the prefix displayed, but will not be part of the MPLS label stack for packets destined for 192.168.10.10.

Label 3 is in use for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10.

Label 0 is used for the prefix displayed and will be part of the MPLS label stack for packets destined for 192.168.10.10.

Page: 1 / 8

Total 102 questions Full Exam Access