23 March, 2023

The Abreast Of The Times Guide To 352-001 Questions Pool

Your success in Cisco 352-001 is our sole target and we develop all our 352-001 braindumps in a way that facilitates the attainment of this target. Not only is our 352-001 study material the best you can find, it is also the most detailed and the most updated. 352-001 Practice Exams for Cisco 352-001 are written to the highest standards of technical accuracy.

Online 352-001 free questions and answers of New Version:

Page: 1 / 20

Total 249 questions Full Exam Access

Question 1

Assume that no multicast optimization is done on LAN switches A and B. Which two features can be used to optimize multicast traffic forwarding in this situation? (Choose two.)

Enable IGMP snooping querier on both switches.

Configure a static MAC entry for the multicast server.

Disable IGMP snooping on both switches.

Disable the IGMP query election process.

Enable PIM snooping on both switches.

Question 2

A financial trading organization plans to monitor the network latency for multicast data feeds on a
hop-by-hop basis. Which technology should be added to their design to support this requirement?

SPAN

NBAR

IPFIX

Precision Time Protocol

Question 3

Which three processes are part of the ITILv3 Service Operation? (Choose three)

Release and deployment management

Problem management

Incident management

Event management

Service-level management

Change management

Question 4

When you design a network that uses IPsec, where can you reduce MTU to avoid network
fragmentation?

on both ends of the TCP connection

on the side closest to the client

on the side closest to the server

in the WAN

Question 5

An enterprise campus is adopting a network virtualization design solution with these requirements
It must include the ability to virtualize the data plane and control plane by using VLANs and VRFs It must maintain end-to-end logical path transport separation across the network
resources available grouped at the access edge
Which two primary models can this network virtualization design be categorized? (Choose two)

Path isolation

Session isolation

Group virtualization

Services virtualization

Edge isolation

Question 6

Which three options are IS-IS design considerations when connecting two Layer 3 switches directly using a 10 GBASE-T cabling and formatting an IS-IS neighbor adjacency?

The default IS-IS network type is point-to-point so a DIS is not elected

A DIS is elected between the IS-IS neighbors and the elected DIS is pre-empted if router with a higher system ID is connected

The area, levels, and interface MTU parameters must match, and system MTU must be unique for two IS-IS routers to become adjacent

Faster IS-IS hello and dead timers increase bandwidth and CPU use, and may cause instability

The IS-IS hello and dead timers should be tuned to detect failures as quickly as possible

A DIS is elected between the IS-IS neighbors and the elected Dis is pre-empted if a router with a lower system ID is connected

The hello and dead timers must match for two IS-IS routers to become adjacent

Question 7

DRAG DROP
Drag the fast Reroute mechanism on the left and drop it onto the corresponding routing protocol on the right
352-001 dumps exhibit

Solution:
A, D, E

Does this meet the goal?

Yes

Question 8

Refer to the Exhibit.
352-001 dumps exhibit

The server is running multiple VLANs on its NIC. Which two Layer 2 features should be applied to the
network location identified by a circle? (Choose two)

UDLD

BPDU guard

BPDU filtering

Port Fast

Loop guard

PortFast trunk

Question 9

You are designing a new multisite data center network within the same city. You are using the newest
routers that run OSPF and DWDM point-to-point interfaces for site-to-site connectivity. Your primary objective is to use the fastest possible method for interface failure detection. Which method achieves this objective?

UDLD

Interface event dampening

LoS/AIS event faults

Fast-hello timers

Question 10

A large enterprise network has a partial mesh network with multiples redundant links. OSPF is used
as IGP and it is implemented in a single-area. The network has slow convergence times and there is a high CPU utilization on the routers. Which solution can address these issues while ensuring that the network scales?

Break the routing domain into separate OSPF areas

Make it a hub-and-spoke topology

Replace OSPF with BGP

Reduce the number of links between routers in the network

Upgrade the routers with higher CPU and memory resources

Question 11

ACME Corporation is integrating IPv6 into their network, which relies heavily on multicastdistribution of data. Which two IPv6 integration technologies support IPv6 multicast? (Choose two.)

6VPE

6PE

dual stack

ISATAP

6to4

IPv6INIP

Question 12

Which two statements regarding to QoS marking are true? (Choose two)

Shaping is one of the ways that packets can be remarked

Class-based marking occurs after packet classification

802.1Q/p CoS bits and IP Precedence are both layer 3 marking fields

QoS marking establishes a trust boundary that scheduling tools depend on

MPLS EXP and DSCP are both layer 2 marking fields

Question 13

Which two application requirements are mandatory for traffic to receive proper treatment when
placed in the priority queue? (Choose two)

WRED drop treatment

Small transactions (HTTP – like behavior)

Tolerance to packet loss

Intolerance to jitter

TCP based application

Question 14

A company requires to connect two data center sites using a hub-and-spoke design. There are 2000
remote sites. It is required to transfer MPLS labeled packets over the public Internet using one router at each remote site. These MPLS labeled packets must be encapsulated inside IP packets. Which solution must be used to simplify this network design?

GET VPN encrypts the MPLS packets with IPsec.

DMVPN dynamically builds GRE tunnels with MPLS encapsulation inside.

Site-to-site IPsec without GRE encapsulates the MPLS packets.

PPPoE encapsulates the MPLS packets

L2TPv3 encapsulated the MPLS packets

Question 15

Refer to the exhibit.
352-001 dumps exhibit

Which data format is used in this REST API call?

JSON

HTMLv5

HTML

XML

BASH

Question 16

Refer the exhibit.
352-001 dumps exhibit

You have designed a IPv6 migration plan, and now you need to determine the impact on the existing
IPv4 network. Which is likely to happen when you enable IPv6 routing on the link between R3 and R2, starting at R3?

R3 advertises the link from R3-R2 to R1, R4 and R5 only.

R2 receives an IPv6 default route from R3.

Only R3 and R2 have IPv4 and IPv6 reachability.

Loopback reachability between all routers for IPv4 is lost.

All routers except R2 are reachable through IPv4.

Question 17

You must make IGP redesign recommendations for a client that has old equipment, with low CPU power and memory, that they do not have budget replace. They are very concerned about CPU load on routers. They are using IS-IS as the IGP in a single l1 area and all routers are connected to each other with point-to-point links. Which method do you recommend to reduce or limit CPU overhead caused by IS-IS?

Use mesh groups to limit flooding of LSAs

Implement wide style metrics for IS-IS on all routers

Select a router to act as a pseudowire to limit topology synchronization

Divide the router into multiple areas and implement address summarization

Question 18

Which two options are IoT use cases that require the low-latency and high reliability that 5G
networks provide? (Choose two)

Sports and Fitness

Smart Home

Automotive

Smart Cities

Industrial Automation

Health and wellness

Question 19

Which OSPF design consideration, with regards to simplicity and address preservation, must be
considered when connecting two Layer 3 switches directly using 10 GBASE-T cabling and formatting an OSPF neighbor adjacency?

Mesh groups must be included in the design

The OSPF Hello and Dead timers must be tuned to detect failures as quickly as possible

The OSPF network type must be set to point-to-multipoint

An OSPF neighbor adjacency formed over loopback interfaces must be placed in Area 0

The OSPF network type must be set to point-to-point

Question 20

DRAG DROP
A small local business recently had an outage after an employee plugged a switch into the corporate network, which caused the traffic pattern in the network to change. You have been tasked to redesign the network so that this does not happen again. From the left side to the right side, drag the PVRST+ features that should be implemented to prevent the corresponding root cause. Not all sources will be used.
352-001 dumps exhibit

Solution:
352-001 dumps exhibit

Does this meet the goal?

Yes

Question 21

Refer to the exhibit.
352-001 dumps exhibit

This layer 2 network is expected to add 150 VLANS over the next year, In addition to the existing 50 VLANs within the network which STP types will support this design requirement the least amount of CPU resource and achieving load balancing?

PVST+

CST

MST

RSTP

Question 22

When designing a network .Which method can be used to control the exit point for traffic an autonomous system, at the layer 3 control plane?

Prepending AS path.

Tuning the multi-exit discriminator.

Setting the site of Origin extended community.

Tuning the metric of the under-tying IGP.

Question 23

In an OSPF network with 20 routers connected together with Ethernet cabling , which topology typically takes the longest to converge?

Full mesh

Ring

Squared

Triangulated

Partial mesh

Page: 1 / 20

Total 249 questions Full Exam Access