05 April, 2025

The Update Guide To 300-425 Dumps Questions

Our pass rate is high to 98.9% and the similarity percentage between our 300-425 study guide and real exam is 90% based on our seven-year educating experience. Do you want achievements in the Cisco 300-425 exam in just one try? I am currently studying for the Cisco 300-425 exam. Latest Cisco 300-425 Test exam practice questions and answers, Try Cisco 300-425 Brain Dumps First.

Page: 1 / 8

Total 100 questions Full Exam Access

Question 1

Which UDP port numbers are used for exchange mobility packets in an AireOS wireless deployment?

UDP 16666 for control plane, EoIP (IP protocol 97) for data plane

UDP 16668 for control plane, UDP 16667 for data plane

UDP 16667 for control plane, UDP 16666 for data plane

UDP 16666 for control plane, UDP 16667 for data plane

Question 2

Which non-Wi-Fi interferer can be identified by Metageek Chanalyzer?

PDAs

jammers

smartphones

printers

Question 3

A customer is concerned about mesh backhaul link security. Which level of ecnryption does the backhaul link use?

hash

AES

WEP

3DES

Question 4

Refer to the exhibit. A client roams between two APs that are registered to two different controllers, where each controller has an interface in the client subnet. Both controllers are running AireOS. Which scenario explains the client roaming behavior?

Controllers exchange mobility control messages (over UDP port 16666) and the client database entry is moved from the original controller to the new controller.

Controllers do not exchange mobility control messages (over UDP port 16666) and the client database, entry is not moved from the original controller to the new conrtoller.

Controllers exchange mobility control messages (over UDP port 16666) and a new client session is started with the new controller.

Controllers exchange mobility control messages (over UDP port 16666) and the client database entry is tunneled from the original controller to the new controller.

Question 5

Where must the APs be mounted when used in a high-density wireless network to provide 6 dB to 20 dB of attenuation to a cell?

in the aisle

under the seat

above the stage

under the stage

Question 6

A wireless engineer must optimize RF performance for multiple buildings with multiple types of construction and user density. Which two actions must be taken? (Choose two.)

Configure FlexConnect groups for each building.

Configure WMM profiles for each building.

Configure AP groups for each area type.

Configure RF profiles for each area type.

Enable DTPC on the network.

Question 7

An engineer has successfully configured high availability and SSO using two Cisco 5508 Wireless LAN Controllers. The engineer can access the Active Primary WLC, but the Secondary Standby WLC is not accessible. Which two methods allow access to the standby unit? (Choose two.)

via the console connection

SSH to the redundancy management interface of the primary WLC

SSH to the service port interface

SSH to the virtual interface of the secondary WLC

SSH to the management interface of the primary WLC

Question 8

A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)

Use a battery pack to power APs

Use a drawing of the office space to draw AP and client placements.

Use DoS attack on APs while measuring the throughput.

Use APs with directional antennas.

Use APs with external antennas.

Use APs with built-in antennas.

Question 9

A network engineer is working on a design for a wireless network that must support data, voice, and location services. To support these services, which access point placement must the engineer use?

corner only

perimeter and corner

perimeter only

indoor and outdoor

Question 10

Which statement about the 9800 Series Wireless Controller mobility tunnel on a Cisco Catalyst 9800 controller is true?

It is an IPsec tunnel with control path only.

It is a CAPWAP tunnel with data path only.

It is a CAPWAP tunnel with control path and data path.

It is an IPsec tunnel with control path and data path.

Question 11

When conducting a site survey for real-time traffic over wireless, which two design capabilities of smartphones and tablets must be considered? (Choose two.)

no support for 802.11ac

higher data rates than laptops

fewer antennas than laptops

no support for 802.11r

lower data rates than laptops

Question 12

What causes the most signal attenuation, based on the wireless design tools?

cinder block wall

metal door

glass wall

office window

Question 13

An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?

The edge of the cell should be -67 dBm.

The edge of the cell should be below 35 RSSI.

The measurement should be done on the 2.4-GHz band.

One AP should be deployed per 3000 square feet.

Question 14

A wireless engineer is utilizing the voice readiness tool in Cisco Prime for a customer that wants to deploy Cisco IP phones. Which dBm range is the network inspected against?

-78 to -65 dBm B.-72 to -67 dBm

85 to -65 dBm

-85 to -67 dBm

Question 15

A high-density wireless network is designed. Which Cisco WLC configuration setting must be incorporated in the design to encourage clients to use the 5 GHz spectrum?

Band Select

RRM

Cisco Centralized Key Management

load balancing

Question 16

Which statement about AP failover priority for access points when configured with priority 1 or 4 is true?

When configured with priority 1, the access point is assigned with the highest priority level and it is marked as critica

This access point fails over before other access points with the lower priority when there is primary controller failure.

When configured with priority 4, the access point is assigned with the highest priority level and it is marked as critica

This access point fails over before other access points with the lower priority when there is primary controller failure.

When configured with priority 4, the access point is assigned with the lowest priority level and it is marked as lo

This access point fails over after other access points with the higher priority when there is primary controller failure.

When configured with priority 1, the access point is assigned with the medium priority level and it is marked as mediu

This access point fails over after other access points with the higher priority when there is primary controller failure.

Page: 1 / 8

Total 100 questions Full Exam Access