27 December, 2024

The Update Guide To NS0-592 Free Exam Questions

Exam Code: NS0-592 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: NetApp Certified Support Engineer - ONTAP Specialist
Certification Provider: Network-Appliance
Free Today! Guaranteed Training- Pass NS0-592 Exam.

Page: 1 / 5

Total 65 questions Full Exam Access

Question 1

A field support engineer has just replaced the IOXM on NODE2 on a FAS8080 running ONTAP 9.1. After the replacement, the customer is unable to perform a giveback because the interconnect is down.
In this scenario, which statement is correct?

Verify that there cross-links between the interconnects.

Verify that the installed FC-VI cards are configured properly.

Verify that the interconnect cables on the motherboard are connected correctly.

Verify that the interconnect cables on the IOXM are connected correctly.

Question 2

You are running a fabric-attached MetroCluster configuration with ONTAP 9.5software. There is a maintenance window for the upcoming weekend. Plexes in your mirrored aggregates between your two data centers have not been synchronizing for two days.
When the resynchronizations begin, they are not as quick as expected, and the process takes more than a day. You have been modifying the number of concurrent I/O streams using the storage raid-options modify raid.
resync.num_concurrent_ios_per_rg command, but the resynchronization speed stays slow.
You have four separate ISLs between your data centers using Brocade 6510 switches. Hardware problems are not an issue.
Which two actions should you take to prevent this problem in the future? (Choose two.)

Update to at least ONTAP 9.4 software.

Restart the resynchronizations after modifying storage raid-options modify raid.resync.num_concurrent_ios_per_rg command.

Avoid changes on your aggregates during the maintenance window.

Take the corresponding plexes offline before maintenance to avoid a base-level synchronization.

Question 3

You are investigating a CIFS issue at a customer site, but it is unclear which SMB version is being used between the client and the server. The customer has provided you with a packet trace output.
In this scenario, which packet exchange contains information to indicate which SMB version was agreed upon by the client and the server?

Ioct1 Request FSCTL_DFS_GET_REFERRALSIoct1 Response FSCTL_DFS_GET_REFERRALS

Session Setup Request Session Setup Response

Negotiate Protocol RequestNegotiate Protocol Response

Tree Connect Request TreeTree Connect Request Response

Question 4

After you replaced the motherboard, the node stopped in the “waiting for the cluster application to come
online” state.
Which two actions should you perform to troubleshoot this problem? (Choose two.)

Check the status of the HA with the interconnect-up field of storage failover show command.

Verify the setting of the cluster interconnect switch.

Verify that the physical links on the cluster ports are up.

Check the status of the cluster with the cluster ring show command.

Question 5

For restore purposes, a storage administrator on an ONTAP system created a FlexClone of a volume that contains a LUN from a specific snapshot. This LUN cannot be seen by a Windows client after a disk rescan is performed by using Disk Management.
In this scenario, which statement is correct?

The cloned LUN must be brought online.

The cloned LUN needs to be mapped to an initiator group.

The cloned volume must be split from the source volume before the LAN can be used.

The cloned LUN must be renamed to a different name than the name of the source LUN.

Question 6

A customer has a 2-node MetroCluster. They experienced a complete power loss at site B. The customer has lost connectivity to site B and now realizes that the DR partner at site A has not taken over the DR partner at site B.
Which two actions must be performed in this scenario? (Choose two.)

On the DR partner at site A, perform the process to switchover.

Ensure that site B is prevented from serving data or simply powered off (nodes and disk shelves).

On the DR partner at site A, perform the process to heal the data aggregates.

On the DR partner at site B, perform the process to heal the root aggregate.

Question 7

A new cluster running ONTAP 9.5 has just been installed and you want to create a FlexGroup volume. Which action will accomplish this task?

Use the storage pool create command.

Use the volume create command.

Use the Deploy utility to provision the FlexGroup volume.

Use the volume size command.

Question 8

Click the exhibit button.
NS0-592 dumps exhibit

A storage administrator reports that when they enabled Vscan, they began receiving reports of CIFS users having very slow access to all their files. The storage administrator recovered from the issue by disabling Vscan on their SVM. The storage administrator was able to collect perfstat output during the time of the reported slow access, as shown in the exhibit.
In this situation, what is the problem?

The problem is on the SVM, as shown in the scan_latency output.

Vscan server 192.168.100.144 was slower than Vscan server 10.23.23.54 in completing Vscan requests.

Vscan server 10.23.23.54 was slower than Vscan server 192.168.100.144 in completing Vscan requests.

The problem was with both Vscan servers 192.168.100.144 and 10.23.23.54.

Question 9

Click the exhibit button.
NS0-592 dumps exhibit

Your customer has severe latency on one of their SATA aggregates. You run the statit -b and statit -e commands to obtain detailed disk statistics.
Referring to the output shown in the exhibit, which disk would be the problem?

0a.11.19

0a.11.21

0a.13.21

0a.11.23

Question 10

A customer reports that one their SVMs has two default gateways. The customer wants to know whether this behavior is expected or if one of gateways should be deleted.
In this scenario, what do you tell the customer?

The configuration is acceptable if the customer configures different metrics on all defaults routes.

The configuration is acceptable only if both default gateways are in the same subnet.

This situation is a misconfiguration, and the customer should delete one of the default gateways because there can be only gateway for each SVM.

The configuration is acceptabl

The customer can achieve load balancing between the default gateways by setting the same metric on all default routes.

Question 11

A customer reports that OnCommand Performance Manager shows that the workload on node-02 in a 4-node cluster has increased to a level that is higher than the threshold. The customer wants to avoid this issue becoming a performance problem.
Which two actions would result in achieving this goal? (Choose two.)

Use the volume move command to move one or more volumes to another aggregate that is owned by another node that is less utilized.

Use the storage aggregate relocation command to offload an aggregate to its partner.

Use the storage aggregate scrub command to verify the parity on the busy aggregates.

Physically move the shelf to another node that is less utilized.

Question 12

Click the exhibit button.
NS0-592 dumps exhibit

When you log in to a node, a warning is displayed as shown in the exhibit. Which statement is correct in this scenario?

The node root volume was moved to a new aggregate.

The partner still hosts the CFO aggregate for the node.

One or more RDB db files are damaged due to an internal software error.

The node cannot communicate with the rest of the nodes in the cluster.

Question 13

You migrated from a FAS3250 system to a new A200 system. After the migration, you notice that data compaction fails to be enabled on the migrated volumes.
In this scenario, which statement is correct?

You need to schedule background deduplication on all volumes.

You need a license to have full efficiency on AFF systems.

Data compaction is not supported on the A200 system.

The volumes are thick-provisioned.

Question 14

A customer is attempting to move from NFSv3 to NFSv4.x and reports that all attempts to mount using NFSv3 continue to be successful, however, all of their NFSv4.x mount attempts fail with an “access denied” error.
Which two statements would cause this error? (Choose two.)

The NFS server does not have NFSv4 enabled.

The SVM’s root volume allows execute access for all users.

The export policy applied to the data volume does not allow clients to access it using NFSv4.

The export policy applied to the SVM’s root volume does not allow the NFSv4 clients to access it.

Question 15

A customer performs a takeover and giveback of their controllers and notices that several of their NFS clients lose access to their volumes for a short period of time during the SFO process. The customer reviewed the LIF failover policies, and the polices are correct.
What is the reason for this behavior?

The clients are using NFSv4 to access the volumes.

The export policies are incorrect and must be updated with node’s HA partner LIF information.

A firewall is blocking the necessary network ports and needs to be updated to allow NFS communication.

NFSv4 file locks need to be broken manually before initiating an SFO operation.

Question 16

When you issue a volume clone create command, which entity in WAFL is copied?

the vol_info block

the buftree

the data block

the inode file

Question 17

A customer reports that a takeover has been disabled on an HA pair. What would be a cause for this to happen?

The HA interconnect is not functioning properly.

There is a disk running too hot.

The interface for the hardware assist has become unavailable.

The cluster network is not functioning properly.

Page: 1 / 5

Total 65 questions Full Exam Access