12 November, 2020

Up To The Minute 600-601 Test Preparation For Managing Industrial Networks With Cisco Networking Technologies Certification

Master the 600-601 Managing Industrial Networks with Cisco Networking Technologies content and be ready for exam day success quickly with this Exambible 600-601 practice exam. We guarantee it!We make it a reality and give you real 600-601 questions in our Cisco 600-601 braindumps.Latest 100% VALID Cisco 600-601 Exam Questions Dumps at below page. You can use our Cisco 600-601 braindumps and pass your exam.

Free demo questions for Cisco 600-601 Exam Dumps Below:

Page: 1 / 9

Total 112 questions Full Exam Access

Question 1

What are two benefits that are provided by proper grounding and bonding systems? (Choose two.)

higher speed communications

safe discharge of electrostatic energy

lower equipment power consumption

equipotential termination points for equipment and cable shields

lowest carbon footprint

Question 2

What should be done with unused conductors in copper unshielded or shielded twisted-pair network cables?

terminate in their characteristic impedance

trim back and properly insulate

connect to protective earth

splice to a used conductor

Question 3

At which Layer would you check for spanning tree loops?

Layer 1

Layer 2

Layer 3

Layer 4

Question 4

Which two reasons make mesh bonding systems most effective? (Choose two.)

cover wide areas

provide additional strength to floor structures

provide low-impedance noise-equalizing paths

create equipotential grounding systems

most cost-effective approach

Question 5

What are two benefits of a star network topology? (Choose two.)

Disruption of the entire network is not required when adding new machines.

Any problem which leaves the network inoperable can be traced to the central hub.

This network type requires less cable as compared to linear bus topology.

The performance of one of the numerous nodes cannot reflect on the performance of other nodes.

The performance of the entire network is directly dependent on the performance of the hub.

Question 6

Exhibit:

Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the exhibit? (Choose three.)

The EtherNet/IP drive connections are in a high-voltage area and need protection from electromagnetic noise, so shielded cable that is rated for 600 V is advised.

EtherNet/IP devices such as the controller, drive, VoIP phone, and IP camera should be in the sameVLAN.

CIP traffic has the highest bandwidth requirement so it needs the highest QoS setting.

EtherNet/IP drive traffic has high sensitivity to random drops, latency, and jitter.

Real-time motion control and VoIP traffic can share the same VLAN with the proper QoS setting.

IEEE1588 and PTP are important for ensuring real-time synchronization.

Question 7

With a Cisco IE 2000 switch, what does a port status LED indicate when it is solid amber?

The port is sending or receiving data.

A link is present.

No link is present.

There is a link fault.

The port is not forwarding.

Question 8

What is the leading cause of fiber-optic link failure?

contaminants

crushed fiber

poor testing practices

bad connectors

Question 9

What is the most critical step to perform when you are using optical fiber connectors?

Cover with dust caps when not in use.

Immerse in alcohol prior to use.

Blow off and carefully wipe down with a tissue before and after each use.

Lightly sand with cloth prior to mating.

Question 10

With a Cisco IE 2000 switch, what does a port status LED indicate when it is alternating green and amber?

The port is sending or receiving data.

A link is present.

No link is present.

There is a link fault.

The port is not forwarding.

Question 11

Exhibit:

Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

These commands need to be added to the configuration:C-router(config)# router eigrp 123C- router (config-router)# network 172.19.0.0

These commands need to be added to the configuration:C-router(config)# router ospf 1C- router(config- router)# network 172.19.0.0 0.0.3.255 area 0

These commands need to be added to the configuration:C-router(config)# router ripC- router(config- router)# network 172.19.0.0

No further routing configuration is required.

Question 12

DRAG DROP

Solution:
600-601 dumps exhibit

Does this meet the goal?

Yes

Question 13

What is the purpose of a time domain reflectometer?

It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems.

It opens shorts and pinholes in cable shielding.

It correlates the returned light pulses with a location in the fiber.

It opens kinks and mismatched cable connectors.

Question 14

Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.)

designated ports

duplex operating mode

fast mode ports

root bridge

root ports

BDPU priority

Question 15

You are troubleshooting a connectivity problem and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. Which command would you issue to see where the packets stop?

router#ping

router#tracert

router#show ip route

router#show cdp neighbors

router#traceroute

Question 16

What is the purpose of Spanning Tree Protocol?

to prevent routing loops

to create a default route

to provide multiple gateways for hosts

to maintain a loop-free Layer 2 network topology

to enhance the functions of SNMP

Question 17

What are two symptoms of duplex mismatch? (Choose two.)

Ping does not return from one direction versus the other direction.

Communication is slow and locks up.

Speed is seen equally slow in both directions.

The half-duplex side sees frame sequence errors or runt frames.

The full-duplex side sees CRC errors.

Question 18

Exhibit:

Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which address is the default gateway of Host 3?

the address of the switch interface that is connected to router interface Fa0/0

the address of the switch interface that is connected to router interface Fa0/1

the address of the host that is connected to Network A

the address of the host that is connected to Network B

the address of the router interface Fa0/0

the address of the router interface Fa0/1

Question 19

With what are APC connectors used?

Category 6a cables that need tight radius bends

copper network cables in corrosive environments

single-mode fiber-optic cables to reduce return loss

high-density copper patch panels

Question 20

At which Layer would you troubleshoot a cabling issue?

Layer 1

Layer 2

Layer 3

Layer 4

Question 21

For which three issues should fiber-optic network segments be tested? (Choose three.)

attenuation

near-end crosstalk

length

polarity

jitter

tensile stress

Page: 1 / 9

Total 112 questions Full Exam Access